Differences

This shows you the differences between two versions of the page.

--- raspberry_pi:mods:mesh [2017/05/25 20:42]
matthias [IPv6 Setup]
+++ raspberry_pi:mods:mesh [2018/02/23 16:54] (current)
matthias [Mesh config script] without cd but use homedir
@@ Line 16: / Line 16: @@
    - Create Mesh setup script & make it bootable
    - Configure Avahi to announce PirateBox
+===== Prereq. =====
+Check the internet is working and sudo is active:
+  sudo touch /tmp/sudo_test
+  sudo rm /etc/resolv.conf
+  sudo sh -c 'echo "nameserver 8.8.8.8" > /etc/resolv.conf'
+  dig google.de | grep -q -e 192.168.77.1 && echo "error, Internet is not working!"
 ===== Software bridge =====
 Create the network configuration file for the bridge:
   cat <<EOF > piratebox_bridge
   Description="General bridge interface for PirateBox"
@@ Line 39: / Line 48: @@
   sudo sed -i -e 's|DO_IFCONFIG="yes"|DO_IFCONFIG="no"|' \
       -e 's|DO_BRIDGE="no"|DO_BRIDGE="yes"|' \
-       /opt/piratebox/conf/piratebox.conf
+      -e 's|DNSMASQ_INTERFACE="wlan0"|DNSMASQ_INTERFACE="br-lan"|' \
+      /opt/piratebox/conf/piratebox.conf
 Edit piratebox.service file for system dependencies
@@ Line 52: / Line 62: @@
 ===== IPv6 Setup =====
-Do the following commands..
+Let's start with fixes on PirateBox 1.1.3
+    sudo sed -i -e 's| radvd|/usr/bin/radvd|g' /opt/piratebox/init.d/piratebox_alt
+Do the following commands..
   PREFIX="fdc0:ffea"
@@ Line 78: / Line 91: @@
      Prefix: /64
   "
+===== Mesh config script =====
+This step assumes, that you have a working network connection and the wifi adapter for mesh is the 2nd (phy1).
+  sudo sh -c 'echo "br_netfilter" > /etc/modules-load.d/netfilter.conf'
+  sudo modprobe br_netfilter
+  sudo pacman -Sy --noconfirm batctl
+  wget https://github.com/PirateBox-Dev/PirateBox-Mesh/releases/download/1.1.4/piratebox-mesh_1.1.4_all_NON_WRT.sh
+  chmod a+x piratebox-mesh_1.1.4_all_NON_WRT.sh
+  sudo mv piratebox-mesh_1.1.4_all_NON_WRT.sh /bin/piratebox-mesh.sh
+  sudo sed -i -e 's|phy0|phy1|g'  \
+     -e 's|MESH_CHANNEL=0|MESH_CHANNEL=6|' \
+     -e 's|EXCHANGE_MAC="yes"|EXCHANGE_MAC="no"|' \
+     /bin/piratebox-mesh.sh
+Create a start/stop script:
+  cat <<EOF > ~/mesh.service
+  [Unit]
+  Description=PirateBox Mesh Service
+  PartOf=netctl@piratebox_bridge.service
+  [Service]
+  Type=idle
+  RemainAfterExit=yes
+  ExecStart=/bin/piratebox-mesh.sh start
+  ExecStop=/bin/piratebox-mesh.sh stop
+  [Install]
+  WantedBy=multi-user.target
+  EOF
+  sudo mv ~/mesh.service /etc/systemd/system
+  sudo systemctl daemon-reload
+  sudo systemctl start mesh.service
+  sudo systemctl enable mesh.service
+===== AVAHI =====
+  sudo mv /etc/avahi /etc/avahi.old
+  sudo ln -s /opt/piratebox/conf/avahi/ /etc/avahi
+  sudo systemctl start avahi-daemon
+  sudo systemctl enable  avahi-daemon
+===== Finalize =====
+At the end you should do a reboot
+  sudo reboot